How to Replace a Bathtub Yourself: Removing and also Replacing.
AppointmentHow do you actually feel on the subject of Installing A Bathtub?
Setting up a tub isn't specifically brain surgery, however it does call for solid plumbing, carpentry, as well as occasionally, tiling abilities. Changing an old bathtub with a new one is additionally a reasonably difficult job. If the old bathtub is conveniently accessible, the project can move immediately; if you need to open a wall to eliminate the old bathtub and also place the new bathtub, the task is much harder. In either situation, the task is within a residence handyman's abilities, although you will need a helper to leave the old bathtub as well as embeded in the brand-new one. Make sure you have actually qualified yourself for the job and are comfortable attempting it. Instead of working with a specialist to take over a halfway-completed job, it is much better to think about using one prior to you start. Opportunities are you might require a specialist plumber to make tube links.
This post will certainly assist you set up a brand-new tub in your shower room if you have actually currently gotten a brand-new bathtub as well as don't need to change the arrangement of your previous supply of water pipes.
Your tools and material checklist need to consist of the following:
Planning for the Setup
First of all, the supporting frame provided with the bathroom must be fitted (if needed) according to the producer's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the tap block, it is essential to make sure that if the faucet features a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bath, it is also reasonable to fit a sustaining plate under the taps device to avoid stress on the bathtub.
Fit the adaptable faucet connectors to the bottom of the two faucets utilizing 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make sure you use every one of the supplied washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath should currently be ready to be suited its final setting.
Removing Old Taps
If you require to replace old faucets with new ones as a part of your setup, then the first thing you must do is disconnect the water system. After doing so, turn on the taps to drain pipes any water staying in the system. The procedure of removing the existing taps can be fairly problematic because of the limited access that is typically the instance.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the taps. Have a fabric all set for the staying water that will certainly come from the pipes. As soon as the supply pipes have actually been removed, utilize the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the single taps from transforming during this process. As soon as the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any type of old sealing compound.
Prior to carrying on to fit the new faucets, contrast the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, after that a shank adapter is required for the new faucets to fit.
Mounting the Bathtub
Utilizing the two wood boards under its feet, position the bathtub in the needed setting. The wood boards are handy in evenly spreading the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 tiny points.
The next goal is to make sure that the tub is leveled all round. This can be attained by examining the level and also readjusting the feet on the bath tub up until the spirit level checks out level.
To install faucets, fit all-time low of the furthest flexible tap adapter to the ideal supply pipeline by making a compression join; then do the very same for the other faucet.
Turn on the supply of water and also inspect all joints and brand-new pipework for leaks and also tighten them if needed. Fill the bath tub as well as likewise check the overflow electrical outlet and also the typical outlet for leakages.
Lastly, fix the bathroom paneling as described in the manufacturer's user's manual. Tiling as well as securing around the tub needs to wait until the tub has actually been utilized at the very least once as this will certainly resolve it into its last position.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to prevent damages to the thread. One end of the port fits on the plastic tail of the tap as well as the other end supplies a link to the existent supply pipelines.
If you require to fit a monobloc, then you will call for reducing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next off, place the tap in the installing opening in the bath/basin making certain that the washers remain in place in between the tap and also the sink. Secure the faucet in place with the maker provided backnut. As soon as the tap is securely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with typical faucet ports. The previous type must be connected to the faucet finishes first, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the area where the bath satisfies the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is essential as the installation can relocate sufficient to crack a rigid seal, triggering the water to pass through the wall between the bath and the tiling, resulting in issues with wetness and possible leaks to the ceiling below.
You can pick from a selection of coloured sealers to blend in your fixtures as well as fittings. They are marketed in tubes as well as cartridges, as well as can securing voids approximately a width of 3mm (1/8 inch). If you have a larger gap to fill up, you can fill it with spins of drenched paper or soft rope. Bear in mind to constantly load the bath tub with water before sealing, to allow for the movement experienced when the tub is in use. The sealant can break relatively very early if you do not think about this activity prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are likewise quickly offered on the marketplace. It is a good idea to fit the tiles using water-resistant or waterproof adhesive and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you like more info about Tools You Need to Install a New Bathtub ? Write a remark below. We will be glad to know your views about this blog post. In hopes to see you back again in the near future. Remember to set aside a second to distribute this post if you enjoyed it. Many thanks for your time invested reading it.
Book Now